Difference between revisions of "Wheel Suspension 5x5"
From Space Engineers Wiki
(Added headers, added information, linked to wheel blocks page, will post screenshots later. Stub removed!) |
m (→Known Issues: adjusted spelling and grammar) |
||
| Line 75: | Line 75: | ||
* You sometimes cannot see antennas or beacons while driving a rover, if it has no thrusters. | * You sometimes cannot see antennas or beacons while driving a rover, if it has no thrusters. | ||
::Workaround - You can add just a frame of thruster somewhere to workaround this. | ::Workaround - You can add just a frame of thruster somewhere to workaround this. | ||
| − | * Settings update bug. If grid is resting on | + | * Settings update bug. If the grid is resting on a flat surface, it can become "frozen". Thus changes you made to, for example, Strength will be visible only when you move the rover or apply any physical interaction to it. Changing Height Offset helps to unfreeze grid too. |
== See Also == | == See Also == | ||
Revision as of 09:02, 6 February 2016
Large Ship / Station
Wheel Suspension 5x5Components
Required
20
Mass (kg):
0
Integrity:
0
Build time (seconds):
30
Active power consumption (MW):
0.002
Power Consumer Group:
Utility
Dimensions (W x H x D):
2 x 3 x 2
Small Ship
Wheel Suspension 5x5Components
Required
Mass (kg):
0
Integrity:
0
Build time (seconds):
15
Active power consumption (MW):
0.002
Power Consumer Group:
Utility
Dimensions (W x H x D):
2 x 3 x 2
Contents
Overview
The Suspension Wheel 5x5 is a two-part functional block made up of the suspension, and the Wheel 5x5. Suspension in Space Engineers are blocks attached to the wheels that allow a vehicle to absorb large amounts of shock and impact from uneven surfaces, and a means to propel itself. With a wide range of properties to configure, it is not solely limited to ground-based vehicles, but any type of creation a player can put together, such as moving platforms, and space elevators.
Usage
- See "Wheel Blocks" for more in-depth explanation and information.
Terminal
- Steering Angle - How far the wheel can steer in ° degrees.
- Steering Speed - How fast the wheel steers.
- Steer Return Speed - How fast the wheel moves back to neutral position after steering.
- Power - How much force in % percent the wheel will have for propelling the vehicle.
- Friction - How much friction the wheel will produce in %. Too much friction can cause the vehicle to flip over in corners, while low friction can cause slipping. The latter is usually the safer behavior.
- Damping - The damper component that will absorb an impact. Set it low (stiff) for even surfaces and high (soft) for bumpy ground.
- Strength - The 'spring' component of a damper that will reset the damper after an impact. Set it high for even surfaces to quickly regain stability and low for bumpy ground to allow the wheels to keep ground contact and to reduce the risk of launching the vehicle into the air.
- Height Offset - Controls the ground clearance by setting the center point the spring will try to hold. A negative value will result in more ground clearance. Make sure not to set it to the limits to keep some space for suspension travel in both directions.
- Suspension Travel - How much the wheel can move upwards and downwards to absorb impacts and keep ground contact. This will not work properly if the height offset is set to its negative or positive limit!
Media
Tips
Known Issues
- You sometimes cannot see antennas or beacons while driving a rover, if it has no thrusters.
- Workaround - You can add just a frame of thruster somewhere to workaround this.
- Settings update bug. If the grid is resting on a flat surface, it can become "frozen". Thus changes you made to, for example, Strength will be visible only when you move the rover or apply any physical interaction to it. Changing Height Offset helps to unfreeze grid too.
See Also
Programming
Update History
| Update 01.038 |
|
