Difference between revisions of "Wheel Suspension 3x3"

From Space Engineers Wiki
Jump to: navigation, search
m (+updating itembox)
Line 12: Line 12:
 
| sairtightness = sometimes
 
| sairtightness = sometimes
 
| sresourcesinkgroup = Utility
 
| sresourcesinkgroup = Utility
| spartof = Real Wheel 3x3
+
| spartof = Wheel 3x3
 
| spowerconsumption = 0.002
 
| spowerconsumption = 0.002
 
| scomponentstructure = 2
 
| scomponentstructure = 2
Line 32: Line 32:
 
| lairtightness = sometimes
 
| lairtightness = sometimes
 
| lresourcesinkgroup = Utility
 
| lresourcesinkgroup = Utility
| lpartof = Real Wheel 3x3
+
| lpartof = Wheel 3x3
 
| lpowerconsumption = 0.002
 
| lpowerconsumption = 0.002
 
| lcomponentstructure = 2
 
| lcomponentstructure = 2

Revision as of 10:02, 11 February 2017


Wheel Suspension 3x3 Icon.png
Large Ship Icon.png
Large Ship / Station
Wheel Suspension 3x3
 
Components
Required

 

 
 
6
 
 
Mass (kg):
0
 
Integrity:
0
 
Build time (seconds):
20
 
Active power consumption (MW):
0.002
 
Airtight:
Yes - depends on orientation
 
Power Consumer Group:
Utility
 
Dimensions (W x H x D):
1 x 2 x 1
 
Part-Of :
Wheel Suspension 3x3 Icon.png
Small Ship Icon.png
Small Ship
Wheel Suspension 3x3
 
Components
Required

 

 
 
1
 
 
Mass (kg):
0
 
Integrity:
0
 
Build time (seconds):
10
 
Active power consumption (MW):
0.002
 
Airtight:
Yes - depends on orientation
 
Power Consumer Group:
Utility
 
Dimensions (W x H x D):
1 x 2 x 1
 
Part-Of :

Overview

The Suspension Wheel 3x3 is a two-part functional block made up of the suspension, and pre-attached attached Wheel 3x3. Suspension in Space Engineers are blocks attached to the wheels that allow a vehicle to absorb large amounts of shock and impact from uneven surfaces, and a means to propel itself. With a wide range of properties to configure, it is not solely limited to ground-based vehicles, but any type of creation a player can put together, such as moving platforms, and space elevators.

Usage

  • See "Wheel Blocks" for more in-depth explanation and information.

Terminal

  • Steering Angle - How far the wheel can steer in ° degrees.
  • Steering Speed - How fast the wheel steers.
  • Steer Return Speed - How fast the wheel moves back to neutral position after steering.
  • Power - How much force in % percent the wheel will have for propelling the vehicle.
  • Friction - How much friction the wheel will produce in %. Too much friction can cause the vehicle to flip over in corners, while low friction can cause slipping. The latter is usually the safer behavior.
  • Damping - The damper component that will absorb an impact. Set it low (stiff) for even surfaces and high (soft) for bumpy ground.
  • Strength - The 'spring' component of a damper that will reset the damper after an impact. Set it high for even surfaces to quickly regain stability and low for bumpy ground to allow the wheels to keep ground contact and to reduce the risk of launching the vehicle into the air.
  • Height Offset - Controls the ground clearance by setting the center point the spring will try to hold. A negative value will result in more ground clearance. Make sure not to set it to the limits to keep some space for suspension travel in both directions.
  • Suspension Travel - How much the wheel can move upwards and downwards to absorb impacts and keep ground contact. This will not work properly if the height offset is set to its negative or positive limit!

Media

Tips

  • The Wheel Suspension comes with an pre-attached Real Wheel 3x3 block that is different to the Wheel 3x3 that can be placed and built from the block selection screen.
  • While the pre-attached wheel block cannot be replaced if destroyed, it can be repaired - always keep an eye on wheel health.
  • Despite shock absorption they are relatively fragile, especially against Weapons fire.

Known Issues

  • You sometimes cannot see antennas or beacons while driving a rover, if it has no thrusters.
Workaround - You can add just a frame of thruster somewhere to workaround this.
  • Settings update bug. If grid is resting on the flat surface, it can become "frozen". Thus changes you made into, for example, Strength will bi visible only when you move the rover or apply any physical interaction to it. Changing Height Offset helps to unfreeze grid too.

See Also

Programming

Update History

Update 01.038
  • Suspension Wheel 3x3 block Introduced